CCTV TerminologyThe ratio of the focal to the effective diameter of the lens, the smaller “1” stop the more light is passed. The “1” stop directly affects the depth of field.
‘2’ WIRE
Transmission medium using the same two wires for transmit and receive channels. Either leased line or dial up.
20mA CURRENT LOOP
Electric signaling method for CCTV used to control remote camera functions, data is sent via a pair of wires, offers greater distance capability and is less susceptible to interference than similar 2 wire transmission systems.
4 WIRE
Transmission system using 2 separate pairs of wires for the transmit and channels. Leased line or dial up can be achieved on PSTN by dialing 2 separate numbers.
AC
Alternating Current
ACTIVITY DETECTION
Simple of video motion detection, activity detection merely produces on alarm indication on change of light levels, often used with video multiplexers to increase the update on cameras when activity is occurring.
ADDRESS
A sequence of bits, a character or a group of characters that identifies a network station.
AES
Auto electronic shutter - the ability of the camera to compensate for moderate light changes in indoor applications without the use of auto iris lenses.
AFC
Automatic Frequency Control - The automatic tracking of an oscillator to a specific narrow range of frequencies.
AGC
Automatic Gain Control - an electronic circuit normally found in cameras which will increase the video signal in low light conditions, in normal operation it will maintain a constant level.
AI
Automatic Iris - a function of a lens that automatically adjusts to varying light levels to allow the correct amount of light to fall upon the image sensor.
ALARM ACTIVATED VCR
A VCR that is triggered to start from the idle position, this can take as long 20 seconds to spool the tape and start recording for a usable picture. If the VCR is in the time laps mode an alarm can take considerably less of a usable picture.
Alarm Input
A connection from an alarm or sensor that triggers the CCTV unit to start recording if activated.
ALARMING
Ability for CCTV equipment to respond to an external input, provide numerous functions such as switch to relevant camera signal and alarm start a VCR.
ALC
Automatic level Control - On all lenses a manual adjustment also known as Peak/Average, a facility to make the lens respond more to the highlights (peak) or more the darker (average) scenes, providing user adjustment information seen in the highlight.
AM
Amplitude Modulation.
AMBIENT LIGHT
The general light level of a given area.
ANALOGUE
An electrical voltage that is proportional to a given input, i.e. a varying output.
ANGLE OF VIEW
The limits of a viewing area of a camera/lens.
APERTURE
The measure of a light gathering capability, the maximum aperture is the minimum ‘F’ stop of a lens, the lower the ‘F’ stop the better.
APERTURE CORRECTION
Switchable correction circuit which electronically the image of a picture.
ARMOUR
Protection given to a cable to provide resistance to damage that may be incurred from being crushed or cut.
ASPECT RATIO
Ratio between the vertical and horizontal image size of a camera sensor, the ratio is 4:3
ASYNCHRONOUS DATA
Most common for of data, where date is passed without any clocks or timing information, uses start and stop bits for synchronisation.
AT COMMANDS
A protocal between a modem and terminal equipment for autodialing and configeration of the modem.
ATTENUATION
Term used to describe the amount of loss seen in a video signal when transmitted from one point to another.
Auto Electronic Shutter
A CCTV camera feature that allows the camera to compensate for moderate light changes in indoor applications without the use of Auto Iris Lenses.
Auto Iris Control
A lens which allows the Aperture to automatically open or close to maintain proper light levels on the faceplate of the camera pickup device.
Auto Gain Control
An electronic circuit used by which the gain of a signal is automatically adjusted as a function of its input or other specified parameter.
Auto White Balance
A feature on color cameras that constantly monitors the light and adjusts its color to maintain white areas.
AUX
Auxilary
A/V
Audio / Video
BACK FOCUS
A mechanical adjustment for focusing a camera, it moves the image sensor in relationship to the lens to accommodate the different back focal lengths of lenses.
BALANCED SIGNAL
Term generally associated with the transmission of video signals over twisted pair cables, a circuit of two conductors equal to each other in voltage but opposite in polarity.
BANDWIDTH
A value expressing the difference between the upper and lower limits though a range of allowable frequencies.
BAUD
The speed of which data is transmitted, i.e.; 1 baud = 1 Bit per second.
BIT
A binary digit, the smallest element of information in a biary system.
BLACK LEVEL
A measure of picture signal level, that matches to a specified maximum limit for black peaks.
BLANKING PERIOD
The period of the composite video signal at black level (0.3V) and below when the retrace occurs.
BLC
Back Light Compensation - an electronic feature of modern CCD cameras to allow viewing of highlighted scenes that would normally be silhouetted, thus providing more detail.
BNC
The most common for of vedio connector in CCTV.
BPS
Bits per second.
BRAOBAND
Communications transmission where the signal isimpressed on a higher frequency carrier.
BRIDGING
The connection of more than one electrical circuit or component in parallel.
Bullet Camera
A type of camera with a bullet like shape. Can be used inside or out. Some come with infrared lighting.
BURN
The image that has stayed permanently onto the sensitive region of a camera or monitor tube.
BUS NETWORK
A topology network which all terminals are attached to a transmission medium serving as a bus.
BYTE
A unit of 8 bits.
C-Mount Camera
C-Mount or Standard Body cameras are designed to accommodate custom lenses. The lenses can be removed and replaced. Standard Body Cameras are the basic model and offer the most diverse range of features.
CABLE EQULAISER
Increases the video signal level by amplification, used on long cable runs to compensate for the loss in video signal level.
CAD
Computer Aided Design.
CAMEO
Term seen in video multiplexer terminology, represents one sixteenth of one area of a full screen.
CAT5
Category 5 (cable) - type of cable most often used in networking applications.
CCD
Charged Coupled Device - modern form of camera imaging device.
CCIR
Video Sync Pattern for most of Europe, Australia and the Middle East - 625 lines 50Hz.
CCTV
Closed circuit Television - A television system used for private purposes and not for public or general broadcast.
CHROMA BURST
A reference signal (4.43Mhz) included in the video signal after the horizontal synchronisation line pulse.
CHROMINANCE
The part of the video signal that contains all the colour information.
CLADDING
In Fibre Optics the outermost region of an optical cable, lees dense than the centre core, acts as an optical barrier to prevent transmitted light leaking away from the core.
CLOCK
A name commonly used for any of the sources of timing signals used in synchronous data transmission.
CMOS
Complementary Metal Oxide Semiconductor - solid state switching devise also used as camera pickup devise - MOS chip.
C-MOUNT
Industry standard thread mounting portion on the rear of a lens. NOTE: a C mount lens can be used on a CS mount camera with 5mm adaptor ring, however a CS mount lens cannot be used on a C mount format camera.
COAXIAL CABLE
A cable containing a centre conductor witha screen around the same axis.
COMET TAILS
A condition that appears on a VDU that is caused by near burn combined with image movement.
COMPOSITE SYNC
A signal containing line and field pules, but has no video information.
COMPOSITE VIDEO
The combination of all electronic information required to produce a video signal. Comprising 0.7 volts video and 0.3 volt sync hence the term 1 volt peak to peak.
COMPRESSED PICTURE
A compressed picture is a full size picture that has been reduced in size while still displaying all of the original screen information.
COMPRESSION
Taking standard video signals and reducing them into compact digital data.
CONDITIONAL REFRESH
A technique by some video transmission systems, once the first image has been constructed only part of the image that changes is subsequently transmitted, allowing high speed updates when little movement is seen, however the speed of image update decreases.
CROSS TALK
Electrical interference caused by electromagnetic or electrostatic coupling by nearby conductors or external sources. Interference between two or more signals in close proximity within a bandpass.
CRT
Cathode Ray Tube - A device that is used to display information on a TV or monitor.
CS TO C MOUNT ADAPTOR
A spacing ring of 5mm that allows the use of C mount lenses CS mount cameras.
CS-MOUNT
Uses the same thread as C mount but requires the lens to be 5mm closer to the image sensor, new industry standard for lens mounting.
DARK CURRENT
The thermally induced current that exist in a photo diode in the absense of incident optical power.
DATA PROTECTION
The correlation between the gathering and
distribution of data, technology, the public expectation of privacy, and
the legal issues involved."
DAT
Digital Audio Tape - a technology for sharing massive amounts of digital information in a small package. Used for archiving digital recorded images.
Day / Night Camera
Not to be confused with Infrared Cameras, "Day/Night Cameras" are regular cameras with a highly sensitive CCD chip with the ability to capture quality imagery with very little light present.
DB
Decibel - A logarithmic ratio between two signals.
DC
Direct Current.
DD
Direct Drive - a new form of auto iris drive for lenses, whereby the lens requires a DC reference from the camera opposed to a video signal required by AI (auto iris) lenses.
DECODE
Seen in multiplexer terminology refer g to the playback of images from tape.
DECOMPRESSION
Taking digitally compressed DVST information and restoring this to normal video images.
DEFINITION
The ability of a camera or monitor to resolve fine detail, measured in lines.
DEPTH OF FIELD
Area of view that is in focus, the depth of field decreases as the lens aperture increases.
DESK TOP SWITCHER
A device to select incoming signals from a number of cameras for display onto one or more monitors.
DIGITAL SIGNAL
A signal that is comprised of binary information i.e.; 1 or 0, to allow processing by microprocessor based equipment.
DISTRIBUTION AMPLIFIER
A device that seperates and amplifies input video signals for multiple outputs.
Dome Camera
A type of camera with a dome-like shape. Most often used indoors. Some feature infrared lightning and some are designed to be tamper-proof, such as the Armor Dome Camera.
DROPOUT
The loss of video signal from a magnetic tape playback head or worn or damaged tapes.
DTMF
Dial Tone Multi Frequency - used by some manufactures for telemetry signaling over twisted pair cables.
DUPLEX
Seen in multiplexer terminology where two simplex units have been assembled as one unit, allowing the equipment to perform two functions simultaneously i.e.; record pictures to tape whilst displaying multiscreen images of cameras at the same time.
DVR
Digital Video recorder, a devise used to record video images directly to a hard drive, the images may then be accessed instantly and archived to CD.
DVST
Digital Video Storage & Transmission - name given to equipment that can compress pictures to a fraction of their former size for transmission over communication networks or for digital storage.
DWELL TIME
The duration a video switcher will stay on a camera before moving onto the next camera.
EI
Electronic Iris - A feature in modern CCD cameras where the camera electronics automatically varies the shutter to mimic an AI (auto iris) lens, allowing the use of fixed or manual iris lenses in a wider range of areas.
EIA
Electronic Industry Association - US TV standard 525 lines 60 fields.
EMI
Electro Magnetic Interference - Electrical or electromagnetic energy that may cause unwanted responses, degradation or failure in electronic equipment.
ENCODE
Seen in multiplexer terminology as the recording of images to tape.
ERROR CORRECTION
Method employed by modems to ensure that data is transmitted and received error free.
EXTERNAL SYNC
The ability of electronic equipment (normally seen in cameras) to accept a sychronisation signal from an external source and sychronise its self to it.
FC
Foot Candle - American measurement of light 10fc = 1lux.
FI
Fixed Iris
FIBRE OPTIC
More efficient method of sending signals than the conventional method of copper cable.
FIELD
One half of a frame comprising 312.5 lines there are 50 fields per second.
FIELD OF VIEW
The image area area produced by any camera/lens combination.
FLANGE LENGTHS
Referring to lenses - C mount = 15.52mm CS mount = 12.5mm
FM
Frequency Modulation.
FOCAL LENGTH
Of a lens and measured in millimetres, has a direct relationship to the angle of view that is obtained, a short focal length provides a wide angle of view and a larger focal length provides a narrower angle of view.
FOCAL POINT
The point of which light passing through a lens is concentrated.
FPS
Frames Per Second - in digital video applications, refers to the number of video images that can be captured, displayed, or recorded in a second. Also referred to as the 'frame rate' or 'refresh rate'.
FRAME TRANSFER
Type of CCD imager used by some cameras.
FREQUENCY REPONSE
The capability of a device to transmit and receive a given range of frequencies.
FRONT PORCH
A portion of a composite video signal that is located at the start of the horizontal blanking pulse and the start of the corresponding sync pulse.
FSK
Frequency Shifted Keying - a form signaling employed by coaxial born telemetry equipment.
FULL PICTURE UPDATE
Used to describe video transmission products that send the total image on each update.
GALANOMETRIC
A method of converting the minute electric currents produced by AI (auto iris) circuits, used by both AI and DD (direct drive) lenses.
GAMMA CORRECTION
Balances the light seen by the camera to that of the monitor.
GEN LOCK
As per external sync, allows cameras to synchronise to a common signal, providing bounce free switching of displayed images.
GHOSTING
Multiple images caused by video signal transmission echoes, not to be confused with ‘burn in’’.
GIGA
Order of magnitude 10-9
GIP
Granded Index File - a measurement shown in the form of a diagram which illustrates how the quality of glass in fibre optics, alters gradually from the densest at the core to the optically less dense cladding.
GLT
Ground Loop Transformer - an isolation transformer with no direct contact between input and output.
GROUND LOOP
Picture interference caused by different earth potentials at each end of video coaxial cable, clearly seen as humbars or interference.
HARDWARE COMPRESSION
Video data compression taken place in specialised purpose built microchips.
HARDWIRED
Direct connection between one product and another, used for control equipment in simple systems.
HAYES COMPATIBILTY
Implies that the modem complies with the Hayes AT command language used by most communications software packages.
HELICAL SCAN
Recording system used by VCR’s, a record/playback head used by VCR’s whereby the head rotates scanning the video tape in helical path.
HORIZONTAL RESOLUTION
The amount of information that can be displayed (measured in lines) upon a VDU.
HZ
Hertz - Cycles per second, method of which frequency is measured.
IDENT
Camera capture or number displayed on a video signal.
ILLUMINANCE
Measurement of light in lumens per square metre, unit of which is Lux.
IMAGE INTENSIFIER
A devise that uses fibre optics to increase the sensitivity of a pick up tube.
IMAGE PLANE
The surface upon which an image is formed in a camera.
IMAGE SENSOE FORMAT
Refers to the size of the image plane within a camera.
IMPEDANCE
Measured in ohms, refers to the conbined resistance and reactance in an electrical circuit.
Infrared Camera
Infrared Security Cameras have special infrared lights installed around the outside of the camera lens. Through use of this special light the camera can capture a good picture even in total darkness.
INTERLACE (2:1)
Refers to the combination of two fields, one odd and one even to produce a single frame.
INTERLEAVING
Term seen in multiplexing, when a camera is alarmed be it via external means PIR (passive infra red movement sensor) or by activity detection then it is recorded more frequently to tape, it is recorded every other camera for instance should camera #4 be triggered then the recording sequence would change.
INTERLINE TRANSFER
Type of CCD chip in which the photosensors aquifer and store an electric charge according to the intensity of light falling on them.
INTERNAL SYNC
Crystal controlled oscillator with a camera that is DC powered.
IP RATING
A rating used to provide an index of protection from elements such as water and dust ingress.
Iris
The Iris (on some lenses) controls how much light is let into the camera lens.
IR LIGHTING
Infra Red lighting that is above the visible wavelength, used for descrete illumination in CCTV systems.
IR SHIFT
Difference in focus of a cameras field of view between wight an IR lighting.
IR TRANSMISSION
Method of sending video signals and/or data over free space, distance and quality of transmission is affected by environmental conditions such as fog and rain.
IRIS
Mechanism within a lens to regulate the amount of light that passes through and falls upon the image sensor.
ISDN
Integrated Services Digital Network - an international standard for voice and data communications offering greatly improved transmission speeds than the older PSTN network.
ISIT
Intensified Silicon Intensified Target - Usually used for extreme low light CCTV cameras or X-ray machines.
ISO
International Standards Organisation
LAG
Image retention that occurs in a video image when rapid motion of the camera or viewed object leaves a trail.
LAN
Local Area Network - Communications network for electronic equipment, limited to a single building or site.
LASER
A source of exceptionally pure light which can concist of a single wavelength concentrated into single beam, used to transmit IR lighting through fibre optic cable.
LEASED LINE
A telephone connection giving a permanent point to point link.
LED
Light Emitting Diode
LINE AMPLIFIER
Device that prepares a signal for transmission over extended cable runs, by amplifying the signal strength.
LINE FED
A camera that is powered down the same cable which it uses to send the video signal information back to the monitor.
LINED LOCKED
A camera that is synchronised to the frequency of its AC power supply.
LINE POWERED
Same as line fed
Lens
The lens of the camera determines the angle of view (Field of View) and the focus of the captured image. There are many different lens options.
LOOPING
A piece of video equipment that allows video signals to pass through with out being terminated.
Low Light
Refers to very dim lighting, even 'normal' darkness. Complete darkness is 0 lux. Infrared cameras work well in very low light conditions.
LUMINANCE
‘ Y ’ - The monochrome element of a video signal.
LUX
Unit of light measurement.
MATRIX SWITCHING
A video switcher that allows any video signal input to be switched to any monitor output.
MCL
Maximum camera length.
MFD
Mode Field Diametre - Term used in fibre optics.
MI
Manual Iris
MICROWAVE TRANSMISSION
Method of sending video signals and/or data over free space, longer distances than IR transmission.
MODE
Path taken by light rays along fibre optic cable.
MODULATION
A process of varying a carrier signal in relation to another signal.
MONITOR
A video display unit used to display images from a camera or computer.
MONOCHROME
Term used for a black & white image.
MOS
Metal Oxide Semiconductor - A form od CCD imager used in CCD cameras.
Mounting Bracket
Various different kinds of mounting brackets are used to install cameras to the wall or ceiling.
MTBF
Mean Time Between Failure - The average time between between equipment or component failure.
MTTR
Mean Time To Repair - The average time it takes to fully repair a piece of equipment.
MULTIMODE
An optical fibre that supports more than one propagation mode.
MULTIPLEXER
A unit that can accept a number of camera inputs and simultaneously display them on a single monitor and/or record them to a single VCR machine, multiplexers can also be used to transmit multiple cameras over the same transmission medium.
MULTIPLEXING
A process in which multiple cameras are transmitted or recorded.
MUX
Multiplexer unit.
ND
Neutral Density
ND FILTER
A glass filter that attenuates the light evenly over the visible spectrum, used to force the lens iris open in order to focus the camera for low light operation.
ND SPOT FILTER
A graduated filter fitted to the centre of a lens, restricting the amount of light that can pass through to the CCD imager eliminating the iris closing completely during bright conditions.
NOISE
This normally appears as a snowy or grainy picture.
NON COMPOSITE VIDEO
A video signal minus synchronisation information.
NTSC
National Television Standards Committee.
Outdoor Camera
Outdoor cameras come in special weatherproof housings that allow them to stand up well in tough weather and temperature conditions.
PAL
Phase Alternate Line - Television standard for most of Europe, Australia and the Middle East.
PANNING
When a camera moves from left to right
PAN & TILT
Pan & Tilt head - A device that will move the camera both horizontally and vertically from a remote location.
PCM
Pulse Coded Modulation
PEAK TO PEAK
A value based on the maximum positive and the maximum negative of a wave form for video the standard is 1Volt.
PEAK WHITE INVERTER
Circuitry that will convert white highlights over a pre-set threshhold to black, useful for car registration recognition with headlights.
PH
Pine Hole, referring to a pin hole lens.
PHOTO DETECTOR
A device fitted to fibre optic link to convert light into electrical signals.
PHOTOCELL
A device used to detect changes in light level to provide automatic operation of lights etc.
PHOTON
Quantum of electromagnetic energy, a particle of light is a photon.
PIGTAIL
Short length of fibre optic cable attached to another component such as a source or coupler.
PIP
Picture In Picture - device used to superimpose one video image over another.
PIXEL
In a digital display a pixel is the smallest individual dot that can be separately illuminated.
PL259
UHF connector commonly replaced by the BNC connector in CCTV systems.
Plug and Play Cable
A cable that makes wiring cameras easy. Each camera needs to have a power wire and video wire (and sometimes an audio wire too), plus the connectors at the end of the wire to plug it in. The plug and play cables have all three wires built into one cable with the connectors already attached. The only disadvantage of plug and play cable is that the signal tends to degrade if run distances. For DVRs - plug and play cables can be run reliably up to 100 ft. For analog systems - plug and play cable can be run up to 400 ft. If you need to run longer distances then you need to use the RG59 Siamese cable.
Post-record
This is a DVR's ability to record after a motion detection event has occurred. It records for a specified amount of time after the event has been triggered, even though the motion may have ceased.
PRE-SETS
Pre-programmed positioning of pan/tilt/zoom/focus functions on cameras or dome cameras activated by an alarm input such as movement sensor or by the system operator.
PROTOCOL
A set of rules governing the flow of information in a communications system.
PSTN
Public Switched Telephone Network - analogue communications network used for day to day telephone and data transmission.
PSU
Power supply Unit
PTZ
Pan-Tilt-Zoom - PTZ cameras allow you to adjust the position ('pan' is side-to-side, 'tilt' is up-and-down) and focus ('zoom') of the camera using a remote controller. Due to this added functionality, these cameras tend to cost much more than non-PTZ cameras
QUAD SPLITTER
A device used to display four camera images at the same time on one monitor.
RACK MOUNT
Piece of equipment that can be housed into a rack enclosure, industry standard is 19inches with the height measured in ‘U’ - 1U = 1.75
RANDOM INTERLACE
Method of television scanning that does not define a strict relationship between adjacent scan lines in sequential fields.
RASTOR
Pre-defined scanning area for a television picture tube.
RCA
An electrical connector invented by Radio Corporation of America, from which its name is derived. Consists of 3 wires - red, yellow, and white, these are commonly used on a wide assortment of products in the audio/video market.
Real-Time Recording
In digital video applications, 30 frames per second per camera (see above) looks just like real-time. There is no hesitation or jerkiness in the video.
REFLECTANCE
Ratio to which is reflected of a given surface, normally shown as a percentage.
REFLECTED LIGHT
Scene illumination multiplied by reflectance, this is the light level available for the camera and determines picture quality.
REGENERTATORS
Units placed at regular intervals along a transmission system to detect weak signals and regenerate them.
Remote Surveillance
The ability to view your cameras from a remote location. Information is transmitted via phone line or internet.
REMOTE SWITCHER
A video swatter within a master control unit that can be controlled remotely by a single coax cable or pair of cables.
REPEATER
A device that amplifies and then re-transmits a signal.
Resolution
Refers to how much detail can be captured on a camera or displayed on a monitor. Cameras typically capture about 380 horizontal lines of resolution. High resolution cameras may capture 450 lines of resolution or more. The higher the resolution, the more detail that can be captured in a picture. The monitors and recording devices can generally handle at least as much resolution as the cameras can capture.
RG59
An RG-59 is a common co-axial cable used in CCTV applications.
RG59 Siamese Cable
This type of cable combines the power wire with the video wire. You have to add your own connectors to each end of the cable. Use this type of cable when you need to run distances longer than 100 ft with a digital system, or more than 400 ft. with an analog system.
RISE TIME
The time required for the leading edge of a pulse to rise from 10% to 90% of its total amplitude.
RS170
Video Sync Pattern for the United States - 525 lines @ 60Hz.
RS232
Communications network.
RS422
Communications network
RS485
Communications network
RX
Receiving equipment
SCANNER
Device for remotely controlling the horizontal movement of a camera (panning).
SCART
Standard European connector for carrying audio and video signals.
SCENE ILLUMINATION
The density of light falling upon a scene to be viewed, measured in Lux.
SCREEN SPLITTER
Device used to display two cameras on a single monitor, splitting the screen either horizontal or vertical.
SECAM
Sequential Colour & Memory - Colour television broadcast system used in France.
SENSITIVITY
For a camera usually specified in Lux to provide indication of light level required to gain a full video signal from the camera.
SHUTTER
Electronic circuit found in many CCD cameras which allows the light gathering period of the camera to manually altered.
SIMPLEX
Term seen in video multiplexers, with a simplex machine you can only perform one function such as if you are reviewing images from tape, you cannot record images or view live images in a multi-screen format.
SIT
Silicon Intensified Target - a CCD camera used in very low light conditions.
SLAVE
A secondary item such as a control position that performs the same or restricted functions of the master unit. SLOWSCAN
Old form of video transmission over telephone networks, replaced by Fastscan and DVST systems.
SN RATIO
Signal to Noise Ratio - the ratio of maximum peak to peak signal voltage to the RMS voltage of the noise at a given time, measured in Decibels.
SOFTWARE COMPRESSION
Video data compression achieved by computer program processing.
SPECTRAL RESPONCE
Sensitivity of an image device to different frequencies of light, visible light is 300 to 730nm IR (infra-red) is 715 - 850nm.
SPEED OF UPDATE
The time taken to refresh a single picture.
SPIKE
An amplitude surge, an undesirable momentary increase in electrical current or signal.
SVHS
Super Video Home System - a higher resolution recording medium than VHS.
SWIVEL MOUNT
Used on camera and housing mounts to allow precise positioning of cameras.
SYNC GENERATOR
A device that produces a synchronisation signal.
SYNCHRONISATION
The occurrence of two or more electrical events at the same time - in sync.
SYNCHRONISATION DATA
Data and synchronisation pulses sent at the same time, used for more sophisticated communications
TA
Terminal Adaptor - used to connect video transmission products to an ISDN digital telephone line.
TDG
Time & Date Generator - device used to superimpose the time and date onto a video image.
TELEMETRY
Electronic signaling method, in CCTV used to remotely control camera functions.
TERMINATION
In CCTV the termination is 75 ohms, if a signal is being looped then the equipment should be set to Hi-Z (un-terminated).
TIME BASE CORRECTION
Method used to align unsynchronised camera signals, widely used by multiplexers and quad splitters.
TIME LAPSE VCR
A VCR that can slow down its recording rate, used to extend the length of recording on a standard 3 hour tape to as much as 960 hours (the greater the time lapse rate the less frames recorded per second).
TOUCH SCREEN CONTROL
Ability to control camera and system controls from the VDU screen, by simply touching the relevant object or icon.
Transformer
A device used to transfer electric energy from one circuit to another, especially a pair of multiply wound, inductively coupled wire coils that effect such a transfer with a change in voltage, current, phase, or other electric characteristic.
TP
Twisted Pair - an electrical conductor that consists of two insulated conductors twisted around each other.
TRANSDUCER
Devise used to convert energy into an electrical signal.
TVL
Television Lines - used to describe the resolution of a camera or monitor (460TVL).
TX
Transmitting equipment
UNBALANCED SIGNAL
Term used for coaxial cable transmission.
UNTERMINATED
Input of a piece of CCTV system that requires to lopped to another piece of equipment for 75ohm termination.
Varifocal
A type of lens that allows that allows manual adjustment between two focal point to provide the require field of view.
VCR
Video Cassette Recorder.
VDU
Video Display Unit.
VERTICAL INTERVAL SWITCHING
Sequential video switchers that wait for the current field has completed its cycle before switching to the next camera, even though the dwell time may have been exceeded, thus reducing the amount of bounce seen between switching images.
VHS
Video Home System - VCR format name given to 1/2 cassette tape used in VCR’s.
VIDEO LAUNCH AMPLIFIER
An amplifier placed between the video source and the transmission cable, used where the signal needs to be processed before being launched over coaxial or twisted pair cables.
VMD
Video Motion Detection - not activity detection, a process of determining motion by complicated electronic analysis of picture signal and or neural computing techniques.
V.24
List of definitions between terminal equipment and modems.
V.34
28800 bps modem for PSTN and leased line circuits.
Waterproof
A device that can be immersed in water and still function properly.
WAVELENGTH
Distance between two points on adjacent waves, the time necessary for a wave to complete a single cycle.
Weatherproof
A device that is weatherproof can be installed outside and stand up to harsh weather conditions and temperatures. However, it does not mean that it is waterproof.
Wireless Camera
Wireless cameras allow the transmission of video and audio data to be transmitted to the receiver without having to run wires (using radio waves).
WDM
Wavelength Division Multiplexing.
WHITE BALANCE
Used in colour CCD cameras. White should be referenced and determined by colour temperature for the truest colour rendition.
WHITE LEVEL
The brightest part of the picture corresponding to 1volt peak to peak (0.7V above black level).
X.21
General purpose interface between data terminal equipment and data circuit terminating equipment for synchronous operation on public data networks (ISDN).
Y/C
Video signal containing separate luminance(y) and chrominance(c) to provide greatly improved picture quality from VCR’s (SVHS)
A lens with a variable elements giving adjustable magnification and differing fields of view in one such as 12:1
